Cabletron Systems ELS10-26 Reference Manual Download Page 115

Page: 115 / 170

ELS10-26 MIB

6-3

lxhwPortType

{lxhwPortEntry 2}

Integer Read-Only

A value indicating the type of port. The values are defined as:

• csma (1) - Ethernet or 802.3 port

• uart (6) - UART port

lxhwPortSubType

{lxhwPortEntry 3}

Integer Read-Only

An integer representing port type. The following values have been
defined:

• csmacd-tpx (13) – 10BASE-T with crossover

• uart-female-9pin (80)

• csmacd-100-tfx (17) – 100BASE-F

• csmacd-100-tpx (16) – 100BASE-T with crossover

lxhwPortDiagPassed

{lxhwPortEntry 4}

Integer Read-Only

An integer representing the status of the port. The following values
have been defined:

• diag-passed (1)

• diag-failed (2)

lxhwAddr

{lxhwPortEntry 5}

Octet String Read-Only

The unique hard-wired 48 bit MAC address for the port.

lxhwUpLink

{lxhw 5}

Integer Read-Only

An integer that specifies if the Fast Ethernet (FE) Up-Link module
is installed. The following values have been defined:

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands