Cabletron Systems ELS10-26 Reference Manual Download Page 72

Page: 72 / 170

2-46

TCP/IP MIB-II

DESCRIPTION

Defines whether or not an interface
supports redundancy.

::= {ctIfEntry 7}

ctIfPort group implementation of this group is optional

The ctIfPort group contains information about the type of port on
the interface i.e., the type of EPIM,TPIM etc. This information is
not available in the interface group of MIB-II.

ctIfPortTable

OBJECT-TYPE

SYNTAXSEQUENCEOF CtIfPortEntry

ACCESS

not accessible

STATUS

mandatory

DESCRIPTION

This defines each conceptual row
within the ctIfPortTable.

INDEX

{ctIfPortNumber}

ctIfPortPortNumber

::= {ctIfPortTable 1}

ctIfPortEntry

OBJECT-TYPE

SYNTAX

{CtIfPortPortNumber}

ACCESS

not accessible

STATUS

mandatory

DESCRIPTION

This defines each conceptual row
within the ctIfPortTable.

INDEX

{ctIfPortNumber}

ctIfPortPortNumber

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands