Cabletron Systems ELS10-26 Reference Manual Download Page 12 | Manualshive

Page: 12 / 170

background image

1-2

Introduction

1.1 RELATED DOCUMENTATION

You may need to refer to the following Cabletron documentation:

•

ELS10-26 User Guide

– contains installation, configuration, and

management instructions for the ELS10-26. It also describes how
to use the Local Console Manager (LCM), which is a
non-intelligent terminal interface to the ELS10-26.

If you need internetworking reference material, you may find the
following books helpful:

•

Interconnections, Bridges and Routers,

Radia Perlman, Addison

Wesley © 1992.

•

Internetworking with TCP/IP: Principles, Protocols, and Architecture

(2nd edition), Volumes I and II, Douglas Comer,
Prentice Hall © 1991.

•

The Simple Book, An Introduction to Management of TCP/IP-based
internets

(2nd edition), Marshall T. Rose, Prentice Hall © 1994.

This manual describes the software interface between the NMS
and the ELS10-26. This is relevant for an ELS10-26 running Version
1.0 software. The NMS communicates with the ELS10-26 software.

The Network Management, or UART, port is the interface to the
Local Console Manager (LCM). LCM is a non-intelligent terminal
interface that can be used to configure and monitor status for the
ELS10-26.

«
...
10
11
12
13
14
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 2

BB-HCM381A - Network Camera

Brand: Panasonic Pages: 28

BB-HCM381A - Network Camera

Brand: Panasonic Pages: 2

Ray 3 Plus Client

Brand: Sun Microsystems Pages: 6

Brand: ?omtime Pages: 62

Brand: Ubiquiti Pages: 23

Brand: iDirect Pages: 52

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

Brand: Altera Pages: 42

Brand: Buffalo Pages: 2

EZ-Extender Analog 120-Pin Probing Board

Brand: Analog Devices Pages: 29

Seven Solutions WR-ZEN Series

Brand: Orolia Pages: 167

Brand: National Instruments Pages: 8

Brand: Lanner Pages: 59

Brand: Nortel Pages: 163

Brand: Baracoda Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands