Cabletron Systems ELS10-26 Reference Manual Download Page 55

Page: 55 / 170

TCP/IP MIB-II

2-29

snmpOutGetResponses

{snmp 28}

Counter Read-Only

The total number of SNMP GetResponse PDUs created by the
ELS10-26.

snmpOutTraps

{snmp 29}

Counter Read-Only

The total number of SNMP Trap PDUs created by the ELS10-26.

snmpEnableAuthenTraps

{snmp 30}

Integer Read-Write

Whether authentication failures should cause the ELS10-26 to
generate authentication-failure Trap PDUs. Values include:

• enabled (1) - generate traps

• disabled (2) - do not generate traps

2.12 CABLETRON INTERFACE GROUP

ctIfTable

{ctIf 1}

This table defines an extension to the interface table.

SYNTAX SEQUENCE OF ctIfEntry

ACCESS not accessible

STATUS mandatory

ctIfEntry

{ctIfTable 1}

This defines each conceptual row within the ctIfTable.

SYNTAX CtIfEntry

ACCESS not accessible

STATUS mandatory

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands