Cabletron Systems ELS10-26 Reference Manual Download Page 51

Page: 51 / 170

TCP/IP MIB-II

2-25

2.11 SNMP MANAGEMENT GROUP

snmp

{mib-2 11}

The TCP/IP SNMP Group parameters are described below.

snmpInPkts

{snmp 1}

Counter Read-Only

The number of SNMP PDUs received by the ELS10-26.

snmpOutPkts

{snmp 2}

Counter Read-Only

The number of SNMP PDUs created by the ELS10-26.

snmpInBadVersions

{snmp 3}

Counter Read-Only

The number of SNMP PDUs received by the ELS10-26 which had
an unsupported SNMP version.

snmpInBadCommunityNames

{snmp 4}

Counter Read-Only

The number of SNMP PDUs received by the ELS10-26 which had
an unrecognized SNMP community name.

snmpInBadCommunityUses

{snmp 5}

Counter Read-Only

The number of SNMP PDUs received by the ELS10-26 which had
an authentication failure.

snmpInASNParseErrs

{snmp 6}

Counter Read-Only

The number of SNMP PDUs received by the ELS10-26 which had
an ASN.1 parsing error while being decoded by the ELS10-26.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands