Cabletron Systems ELS10-26 Reference Manual Download Page 124 | Manualshive

Page: 124 / 170

background image

6-12

ELS10-26 MIB

lxswdisWriteStatus

{lxswdis 3}

Integer Read-Only

The status of the erase/write operation. The possible values are:

• in-progress (1) - An operation is currently in progress.

• success (2) - The last operation completed successfully.

• config-error (3) - Configuration EPROM encountered an error.

• flash-error (4) - Flash EPROM encountered an error.

• config-and-flash-errors (5) - Both Configuration EPROM and

Flash EPROM encountered errors.

lxswdisConfigIp

{lxswdis 4}

IP Address Read-Write

The IP address of the NMS (i.e., any IP host) that is allowed to use
TFTP to send/retrieve the configuration file of the ELS10-26. A
value of 0.0.0.0 (which is the factory specified default) prevents
any NMS from obtaining access, while a value of 255.255.255.255
gives every NMS permission.

lxswdisConfigRetryTime

{lxswdis 5}

Integer Read-Write

The number of seconds that the ELS10-26 will wait for an
acknowledgment before it retransmits an unacknowledged TFTP
data block. The factory specified default is 5 seconds.

slxwdisConfigTotalTimeout

{lxswdis 6}

Integer Read-Write

The number of seconds that the ELS10-26 will wait for an
acknowledgment to a data block before it cancels a TFTP session.
The factory specified default is 25 seconds.

«
...
122
123
124
125
126
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: D-Link Pages: 11

Brand: D-Link Pages: 8

AirPlus DWL-810

Brand: D-Link Pages: 8

Brand: D-Link Pages: 12

Brand: D-Link Pages: 84

NetDefend DFL-260E

Brand: D-Link Pages: 328

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

DFL-210 - NetDefend - Security Appliance

Brand: D-Link Pages: 19

Brand: D-Link Pages: 22

Brand: D-Link Pages: 4

Brand: Dahua Pages: 12

NetDefend DFL-1600

Brand: D-Link Pages: 23

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

Elinx EIRP305-T

Brand: B&B Electronics Pages: 19

Brand: NAIM Pages: 2

Brand: CAME Pages: 19

Brand: NEC Pages: 6

Brand: Vivotek Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands