Cabletron Systems ELS10-26 Reference Manual Download Page 53

Page: 53 / 170

TCP/IP MIB-II

2-27

snmpInTotalSetVars

{snmp 14}

Counter Read-Only

The total number of MIB objects which have been successfully
altered by the ELS10-26 as a result of SNMP SetRequest PDUs.

snmpInGetRequests

{snmp 15}

Counter Read-Only

The total number of SNMP GetRequest PDUs received by the
ELS10-26, which have been processed with no errors.

snmpInGetNexts

{snmp 16}

Counter Read-Only

The total number of SNMP GetNext PDUs received by the
ELS10-26, which have been processed with no errors.

snmpInSetRequests

{snmp 17}

Counter Read-Only

The total number of SNMP SetRequest PDUs received by the
ELS10-26, which have been processed with no errors.

snmpInGetResponses

{snmp 18}

Counter Read-Only

Always zero, since the ELS10-26 ignores all SNMP response PDUs.

snmpInTraps

{snmp 19}

Counter Read-Only

Always zero, since the ELS10-26 ignores all SNMP Trap PDUs.

snmpOutTooBigs

{snmp 20}

Counter Read-Only

The total number of SNMP PDUs created by the ELS10-26, with a
value of “tooBig” in the PDU’s “ErrorStatus”.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands