Cabletron Systems ELS10-26 Reference Manual Download Page 76

Page: 76 / 170

2-50

TCP/IP MIB-II

is being described. com1 = 1,
com2 = 2

{ctCpEntry 1}

ctCpFunction

OBJECT-TYPE

SYNTAXINTEGER {lm(1), Local Management (default),

ups (2) UPS, slip (3) SLIP, ppp
(4) PPP}

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

Defines the Com Port Function sup-
ported by that Com Port.

{ctCpEntry 2}

ctIfNum

OBJECT-TYPE

SYNTAXINTEGER

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

This defines the interface that is
being described. This is the same as
ifIndex. This is only valid if ctCp-
Function is SLIP or PPP, otherwise 0.

{ctCpEntry 3}

ctCpAdminStatus

OBJECT-TYPE

SYNTAXINTEGER {disabled (1), enabled (2) (default)}

ACCESS

read-write

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands