Cabletron Systems ELS10-26 Reference Manual Download Page 67

Page: 67 / 170

TCP/IP MIB-II

2-41

OBJECT-TYPE

SYNTAX DisplayString(SIZE (8))

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

The current date, as measured by the
device. The representation shall use
the standard MMDDYY format.

::= {commonDev 2}

comDeviceBoardMap

OBJECT-TYPE

SYNTAXINTEGER

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

Contains a bit encoded representa-
tion of slots that contain MIM
boards. If a bit is one, then that slot is
occupied by a board.

::= {commonDev 3}

ctIF group implementation of this group is optional.

The ctIf group contains information about the type of interface, i.e.
the type of BRIM etc. This information is not available in the
interface group of MIB-II.

ctIfTable

OBJECT-TYPE

SYNTAXSEQUENCE OF CtIfEntry

ACCESS

not accessible

STATUS

mandatory

DESCRIPTION

This table defines an extension to the
interface table.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands