Cabletron Systems ELS10-26 Reference Manual Download Page 28 | Manualshive

Page: 28 / 170

background image

2-2

TCP/IP MIB-II

the Cabletron MIB sysID object, i.e., {1 3 6 1 4 1 97 5 7}. Special
versions of the ELS10-26, made for third-party vendors may use
different values for sysID.

sysUpTime

{system 3}

TimeTicks Read-Only

The time, in centiseconds, since the ELS10-26 was last booted.

sysContact

{system 4}

DisplayString Read-Write

The name and address of the contact person for the ELS10-26.

sysName

{system 5}

DisplayString Read-Write

The Internet name of the contact person for the ELS10-26. The
LCM prompt consists of sysName followed by “>”. (LCM is a
non-intelligent terminal interface that can be used to configure and
monitor status for the ELS10-26.)

sysLocation

{system 6}

DisplayString Read-Write

The physical location of the ELS10-26.

sysServices

{system 7}

Integer Read-Only

The sum of the services supported by the ELS10-26. Values
include:

(2)

the ELS10-26 is a bridge only

2.2 INTERFACES GROUP

interfaces

{mib-2 2}

The TCP/IP Interfaces Group parameters are described below.

«
...
26
27
28
29
30
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Brand: Ubiquiti Pages: 50

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 5

Brand: Konica Minolta Pages: 38

Brand: Western Digital Pages: 8

Brand: WaiLan Pages: 27

Brand: IBA Pages: 33

Brand: Toto Link Pages: 55

Brand: SyChip Pages: 24

Brand: Supersonic Pages: 46

Brand: Tripp Lite Pages: 3

Brand: Dataprobe Pages: 16

Brand: Xantech Pages: 16

Brand: H3C Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands