Cabletron Systems ELS10-26 Reference Manual Download Page 33 | Manualshive

Page: 33 / 170

background image

TCP/IP MIB-II

2-7

ifOutOctets

{ifEntry 16}

Counter Read-Only

The total number of bytes transmitted out the port, counting the
MAC header and FCS.

ifOutUcastPkts

{ifEntry 17}

Counter Read-Only

The number of non-multicast packets transmitted out the port,
regardless of whether or not hardware transmission errors were
encountered.

ifOutNUcastPkts

{ifEntry 18}

Counter Read-Only

The number of multicast packets transmitted out the port,
regardless of whether or not hardware transmission errors were
encountered.

ifOutDiscards

{ifEntry 19}

Counter Read-Only

The number of packets to be transmitted out the port, but were not
transmitted due to non-error reasons. The definition of non-error
reasons is implementation dependent. The ELS10-26 defines
non-error reasons as packet congestion. Packet congestion occurs
when too many packets are to be queued for transmission, or when
packets have been awaiting transmission for too long a time
period.

ifOutErrors

{ifEntry 20}

Counter Read-Only

The number of packets that were to be transmitted out the port,
but incurred transmission hardware errors.

«
...
31
32
33
34
35
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: Accelerated Pages: 10

Brand: Accelerated Pages: 4

Elinx EIRP305-T

Brand: B&B Electronics Pages: 19

Brand: T&D Pages: 122

NetStructure ZT 5515

Brand: Intel Pages: 90

Brand: Digisol Pages: 22

Brand: Ubiquiti Pages: 23

IE-SW-PL09M-5GC-4GT

Brand: Weidmuller Pages: 15

Brand: UNICORECOMM Pages: 19

Brand: ADTRAN Pages: 136

Brand: Sennheiser Pages: 22

IPSec VPN Client Zyxel ZyWall 10

Brand: TheGreenBow Pages: 12

StorageWorks TM RAID Array 3000 Pedestal Storage Subsystem

Brand: Compaq Pages: 112

Brand: VIA Technologies Pages: 2

Brand: ADTRAN Pages: 4

Brand: Paradyne Pages: 1

BNI EIP-508 05-Z015 Series

Brand: Balluff Pages: 74

Brand: Advantage Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands