Cabletron Systems ELS10-26 Reference Manual Download Page 135

Page: 135 / 170

ELS10-26 MIB

6-23

• duplex-half (2)

• duplex-full (3)

6.1.8 Cabletron UART Interface Group

lxuartTable

{lxuart 1}

Not Accessible

A list of interface entries; one per UART port.

lxuartEntry

{lxuartTable 1}

Not Accessible

A set of objects for an interface entry. The individual components
are described below.

lxuartIndex

{lxuartEntry 1}

Integer Read-Only

The ELS10-26’s port number of the port. This is always 25.

lxuartBaud

{suartEntry 2}

Integer Read-Write

This is the desired baud rate. Only 1200 baud through 19,200 baud
are supported by the ELS10-26, but the complete set of possibilities
is:

• external-clock (1)

• 1200-baud (2)

• 2400-baud (3)

• 4800-baud (4)

• 9600-baud (5)

• 19200-baud (6)

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands