Cabletron Systems ELS10-26 Reference Manual Download Page 156

Page: 156 / 170

6-44

ELS10-26 MIB

DESCRIPTION

The IP address which is to be the
destination of the traceroute
request. This variable cannot be
set while traceOperation is on.

::= {lxtraceEntry 2}

lxtraceMaxTTL OBJECT-TYPE

SYNTAX

INTEGER

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

The maximum time-to-live for
outgoing traceroute probe pack-
ets. This determines the number
of hops that can be in a tracer-
oute. This variable cannot be set
while lxtraceOperation is on.

::= {lxtraceEntry 3}

lxtraceDataSize OBJECT-TYPE

SYNTAX

INTEGER

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

The size of the datagram sent
with each probe. This variable
cannot be set while lxtraceOpera-
tion is on.

::= {lxtraceEntry 4}

lxtraceNumProbes OBJECT-TYPE

SYNTAX

INTEGER

ACCESS

read-write

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands