Cabletron Systems ELS10-26 Reference Manual Download Page 50 | Manualshive

Page: 50 / 170

background image

2-24

TCP/IP MIB-II

udpLocalAddress

{udpEntry 1}

IP Address Read-Only

The all zeroes IP address (0.0.0.0), which indicates that the UDP
listener is willing to accept UDP datagrams for any IP address
associated with the ELS10-26.

udpLocalPort

{udpEntry 2}

Integer Read-Only

The UDP port number, i.e., one of 69, 161, and 520. Note that
reception of SNMP Traps (UDP port number 162) is not supported
by the ELS10-26.

2.8 EGP GROUP

egp

{mib-2 8}

The EGP Group is not supported since the ELS10-26 does not
support EGP.

2.9 OIM SUBTREE

cmot

{mib-2 9}

The OSI Subtree, as defined in OSI internet management,
Management Information Base, RFC 1214 (L. LaBarre, editor), dated
April 1991, is not supported.

2.10 TRANSMISSION GROUP

transmission

{mib-2 10}

The supported TCP/IP Transmission Group parameters are
described in later sections of this document. The transmission
group supported is:

dot3

{transmission 7}

«
...
48
49
50
51
52
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: H3C Pages: 1057

Brand: Panasonic Pages: 4

Brand: JCG Pages: 3

Brand: National Instruments Pages: 9

Brand: Freescale Semiconductor Pages: 921

Brand: H3C Pages: 3

HHM Series HHM2409

Brand: TDK Pages: 2

Brand: Aurora Pages: 6

Brand: Intel Pages: 20

RoteFinder RF500S

Brand: Multi-Tech Pages: 134

Brand: Planet Pages: 66

RouteFinder RF560VPN

Brand: Multitech Pages: 82

Brand: Cypress Semiconductor Pages: 31

Brand: NEC Pages: 170

Brand: ICP DAS USA Pages: 60

Brand: Icop Pages: 31

Brand: Billion Pages: 2

Brand: Curtiss-Wright Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands