Cabletron Systems ELS10-26 Reference Manual Download Page 11 | Manualshive

Page: 11 / 170

background image

1-1

CHAPTER 1

INTRODUCTION

This manual is for system administrators responsible for
configuring, monitoring, and maintaining the ELS10-26. Much of
the configuration of the ELS10-26 needs to be done using an
SNMP-based network management station. This manual contains
the SNMP MIB variables you may need to configure, monitor, and
manage your ELS10-26. You should use this manual with the

ELS10-26 User Guide

and with the documentation provided with

your NMS.

The contents of each chapter are described below.

• Chapter 1,

Introduction

, provides an overview of the SNMP

primitives, describes the functions the MIB variables can be used
to perform, and describes how to use TFTP to download the
ELS10-26 system software.

• Chapter 2,

TCP/IP MIB-II

, describes the standard TCP/IP MIB

variables.

• Chapter 3,

Ethernet MIB

, describes the standard Ethernet MIB

variables.

• Chapter 4,

Bridge MIB

, describes the Bridge MIB variables.

• Chapter 5,

PPP MIB

, describes the PPP link control and IP table

MIB variables.

• Chapter 6,

ELS10-26 MIB

, describes the Cabletron enterprise

MIB variables.

• Chapter 7,

Traps

, describes generic and enterprise-specific

traps.

«
...
9
10
11
12
13
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: dbx Pages: 8

Brand: XMG Pages: 5

Brand: Habitat Pages: 48

Brand: NAD Pages: 2

Brand: Data Translation Pages: 98

Brand: Ubiquiti Pages: 3

Brand: Draytek Pages: 8

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

USB-BRIDGEV2-EVAL

Brand: IDT Pages: 11

Brand: Justec Pages: 61

Brand: ADTRAN Pages: 2

Brand: Abocom Pages: 63

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

Brand: Longshine Pages: 35

Brand: ZoneVu Pages: 15

Brand: FUNcube Pages: 23

Brand: Abit Pages: 22

Suzie-Q 541.35.520

Brand: Hafele Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands