Cabletron Systems ELS10-26 Reference Manual Download Page 111 | Manualshive

Page: 111 / 170

background image

PPP MIB

5-13

network protocol’s finite state machine. The ELS10-26 only
supports open (1).

pppIpConfigCompression

{pppIpConfigEntry 2}

Integer Read-Write

If none (1), then the local node will not attempt to negotiate any IP
Compression option. Otherwise, the local node will attempt to
negotiate compression mode indicated by the enumerated value.
Changes to this object take effect when the link is next restarted.
The other option Van-Jacobsen TCP/IP header compression (2), is
not supported on the ELS10-26.

«
...
109
110
111
112
113
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: C4i Pages: 8

Brand: Udoo Pages: 7

Brand: Ubiquiti Pages: 3

Brand: REXROTH Pages: 68

Brand: Campbell Pages: 38

Brand: Grizzly Pages: 9

Brand: ZALMAN Pages: 11

Brand: ACTi Pages: 12

Brand: ebm-papst Pages: 13

SFD-2 MkIII Jumper

Brand: Anthem Audio Pages: 2

B-Control Fader BCF2000

Brand: Behringer Pages: 13

Brand: Z-Wave Pages: 42

Brand: National Instruments Pages: 121

Brand: Paradyne Pages: 74

Brand: ALIBI Pages: 232

Brand: Edge-Core Pages: 64

Brand: Comelit Pages: 140

TigerSwitch 100 SMC6924VF

Brand: SMC Networks Pages: 174

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands