Cabletron Systems ELS10-26 Reference Manual Download Page 46

Page: 46 / 170

2-20

TCP/IP MIB-II

icmpInSrcQuenchs

{icmp 6}

Counter Read-Only

The number of ICMP “Source Quench” messages received.

icmpInRedirects

{icmp 7}

Counter Read-Only

The number of ICMP “Redirect” messages received.

icmpInEchos

{icmp 8}

Counter Read-Only

The number of ICMP “Echo (request)” messages received.

icmpInEchoReps

{icmp 9}

Counter Read-Only

The number of ICMP “Echo Reply” messages received.

icmpInTimestamps

{icmp 10}

Counter Read-Only

The number of ICMP “Timestamp (request)” messages received.

icmpInTimestampsReps

{icmp 11}

Counter Read-Only

The number of ICMP “Timestamp Reply” messages received.

icmpInAddrMasks

{icmp 12}

Counter Read-Only

The number of ICMP “Address Mask Request” messages received.

icmpInAddrMaskReps

{icmp 13}

Counter Read-Only

The number of ICMP “Address Mask Reply” messages received.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands