Cabletron Systems ELS10-26 Reference Manual Download Page 134 | Manualshive

Page: 134 / 170

background image

6-22

ELS10-26 MIB

lxdot3TxBabbles

{lxdot3Entry 8}

Counter Read-Only

4

Counter indicating the number of packets transmitted with babble
errors.

lxdot3TxCollisions

{lxdot3Entry 9}

Counter Read-Only

Counter indicating the total number of transmit collisions.

lxdot3SpeedSelection

{lxdot3Entry 13}

Integer Read-Write

Speed may only be selected for the Fast Ethernet Ports. In addition,
the speed -10 mbit option (2) may only be selected for Fast
Ethernet copper ports.

The returned value reflects what has been selected, not the actual
speed value; e.g. the port may actually be 10 or 100 Mbps, but
speed-auto will be the value returned if it was previously selected.

• speed - 10mbit (1)

• speed - 100mbit (2)

• speed - auto (3)

lxdot3DuplexSelection

{lxdot3Entry 14}

Integer Read-Write

All duplex options are valid for all 10 and 100 Mbps ports. The
returned value reflects what has been selected, not the actual
duplex value; e.g. the port may actually be in half-duplex or full
duplex mode, but duplex-auto will be the value returned if it was
previously selected.

• duplex-auto (1)

4.

These statistics are only updated if the ELS10-26 has been configured to gather

extended statistics (lxadminStatsExtended).

«
...
132
133
134
135
136
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: D-Link Pages: 15

Brand: D-Link Pages: 2

Brand: CAME Pages: 19

Brand: F-SECURE Pages: 19

grandMA2 Series

Brand: MA lighting Pages: 36

OXTOPUS EIA-709

Brand: OCCITALINA Pages: 54

Brand: Campbell Pages: 38

Brand: Keithley Pages: 71

Brand: Endace Pages: 51

Brand: Keithley Pages: 98

System Storage DS3200

Brand: IBM Pages: 2

Brand: 3Com Pages: 32

Brand: ADIC Pages: 140

Brand: National Instruments Pages: 80

Brand: Advantech Pages: 108

Comet 3356P-LAN

Brand: ZyXEL Communications Pages: 38

Advanced Flame 1.0

Brand: Eastern Voltage Research Pages: 12

Brand: ADTRAN Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands