Cabletron Systems ELS10-26 Reference Manual Download Page 152

Page: 152 / 170

6-40

ELS10-26 MIB

::= {lxpingEntry 9}

lxpingMax OBJECT-TYPE

SYNTAX

TimeTicks

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

The maximum round trip time
for the ping requests and
responses, in centiseconds.

::= {lxpingEntry 10}

lxpingAvg OBJECT-TYPE

SYNTAX

TimeTicks

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

The average round trip time for
the ping requests and responses,
in centiseconds.

::= {lxpingEntry 11}

lxpingNumTransmitted OBJECT-TYPE

SYTAX

INTEGER

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

The number of ICMP
ECHO_REQUEST messages that
have been transmitted during
this ping request.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands