Cabletron Systems ELS10-26 Reference Manual Download Page 147

Page: 147 / 170

ELS10-26 MIB

6-35

• critical (5)

6.1.13 Ping Management MIB

lxpingDataTimeout OBJECT-TYPE

SYNTAX

TimeTicks

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

The time, in centiseconds, from
the last ping activity (a send or
receive of an ECHO_RESPONSE
or ECHO_REQUEST message),
to when the lxpingEntry infor-
mation for that ping request will
be deleted.

::={lxpingMgt 1}

lxpingTable OBJECT-TYPE

SYTAX

SEQUENCE OF lxpingEntry

ACCESS

not-accessible

STATUS

mandatory

DESCRIPTION

The set of information describing
the active ping requests and their
results.

::={lxpingMgt2}

lxpingEntry OBJECT-TYPE

SYNTAX

lxpingEntry

ACCESS

not-accessible

STATUS

mandatory

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands