Cabletron Systems ELS10-26 Reference Manual Download Page 52 | Manualshive

Page: 52 / 170

background image

2-26

TCP/IP MIB-II

snmpInBadTypes

{snmp 7}

Counter Read-Only

All GetResponse PDUs indicate a noSuchName ErrorStatus, since
this variable is no longer used.

snmpInTooBigs

{snmp 8}

Counter Read-Only

Always zero, since the ELS10-26 ignores all SNMP response PDUs.

snmpInNoSuchNames

{snmp 9}

Counter Read-Only

Always zero, since the ELS10-26 ignores all SNMP response PDUs.

snmpInBadValues

{snmp 10}

Counter Read-Only

Always zero, since the ELS10-26 ignores all SNMP response PDUs.

snmpInReadOnlys

{snmp 11}

Counter Read-Only

Always zero, since the ELS10-26 ignores all SNMP response PDUs.

snmpInGenErrs

{snmp 12}

Counter Read-Only

Always zero, since the ELS10-26 ignores all SNMP response PDUs.

snmpInTotalReqVars

{snmp 13}

Counter Read-Only

The total number of MIB objects which have been successfully
retrieved by the ELS10-26 as a result of SNMP GetRequest or
GetNext PDUs.

«
...
50
51
52
53
54
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: D-Link Pages: 28

Brand: D-Link Pages: 2

DIR-655 - Xtreme N Gigabit Router Wireless

Brand: D-Link Pages: 3

Brand: D-Link Pages: 11

Brand: D-Link Pages: 12

Brand: D-Link Pages: 12

Brand: D-Link Pages: 24

Brand: D-Link Pages: 20

Brand: D-Link Pages: 44

Brand: D-Link Pages: 52

Brand: D-Link Pages: 103

Brand: Magnat Audio Pages: 2

Univerge SV9300

Brand: NEC Pages: 26

Brand: NEC Pages: 20

DS2000 IntraMail

Brand: NEC Pages: 2

SmartSwitch Router

Brand: Cabletron Systems Pages: 338

Brand: IBM Pages: 63

Brand: iDirect Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands