Cabletron Systems ELS10-26 Reference Manual Download Page 139

Page: 139 / 170

ELS10-26 MIB

6-27

lxtrunkState

{lxtrunkEntry 2}

Integer Read-Only

Indicates the trunking condition for this port. Values include:

• off (1) – this link has not been enabled for trunking.

• closed (2) – this link has not yet received any PDUs.

• oneway (3) – incoming trunking PDUs do not indicate that the

ELS10-26’s PDUs are being successfully received by the far end.

• joined (4) – this link is actively participating in the trunk group.

• perturbed (5) – this link is actively participating in the trunk

group; however, the transmission of data packets has been
temporarily stopped due to a change in membership of the
trunk group.

• helddown (6) – an error has been detected and this link is being

held out of service until the error clears.

• broken (7) – this link has been configured for trunking but the

port is physically non-operational.

lxtrunkRemoteBridgeAddr

{lxtrunkEntry 3}

Octet String Read-Only

The MAC address portion of the bridge ID of the remote bridge.

lxtrunkRemoteIp

{lxtrunkEntry 4}

IP Address Read-Only

The IP address of the remote bridge.

lxtrunkLastError

{lxtrunkEntry 5}

Integer Read-Only

The reason for failure when the link is in the held-down state.
Values include:

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands