Cabletron Systems ELS10-26 Reference Manual Download Page 120

Page: 120 / 170

6-8

ELS10-26 MIB

• false (2)

lxadminAuthenticationFailure

{lxadmin 8}

IP Address Read-Only

All nulls, or the IP source address within the last SNMP PDU
which caused an SNMP authentication failure.

lxadminNAMReceiveCongests

{lxadmin 10}

Counter Read-Only

Number of packets not received due to internal buffer congestion.

lxadminArpEntries

{lxadmin 11}

Counter Read-Only

The number of ARP entries for all interfaces.

lxadminArpStatics

{lxadmin 12}

Counter Read-Only

The number of statically defined ARP entries for all interfaces.

lxadminArpOverflows

{lxadmin 13}

Counter Read-Only

The number of times an ARP entry could not be learned due to
insufficient address table space.

lxadminIpEntries

{lxadmin 14}

Counter Read-Only

The number of IP Routing Database entries.

lxadminIpStatics

{lxadmin 15}

Counter Read-Only

The number of statically defined IP Routing Database entries.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands