Cabletron Systems ELS10-26 Reference Manual Download Page 63

Page: 63 / 170

TCP/IP MIB-II

2-37

ctCpAdminStatus

{ctCpEntry 4}

DESCRIPTION

The administrative state of the Com Port.

SYNTAX INTEGER {disabled(1), enabled(2)}

ACCESS read-only

STATUS mandatory

OBJECT IDENTIFIER: 1.3.6.1.4.1.52.4.3.3.4.1.1.4

The OID will actually be 1.3.6.1.4.1.52.4.3.3.4.1.1.4.1 because we
only have the one UART port.

We don’t allow this port to be turned on or off. Because of this, it
will be READ-ONLY.

It will always return enabled (2).

2.15 SNMP VERSION GROUP

enableSNMPv1 Not Supported

{ctSNMP 1}

This object allows control over the SNMPv1 protocol. If set to a
value of disable(1) then the SNMPv1 protocol will not be accepted
by the device.

SYNTAX INTEGER {disabled(1), enabled(2)}

ACCESS read-write

STATUS mandatory

enableSNMPv2 Not Supported

{ctSNMP 2}

This allows control over the SNMPv2 protocol. If set to a value of
disable(1) then the SNMPv2 protocol will not be accepted by the
device.

SYNTAX INTEGER {disabled(1), enabled(2)}

ACCESS read-write

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands