Cabletron Systems ELS10-26 Reference Manual Download Page 36

Page: 36 / 170

2-10

TCP/IP MIB-II

ipInReceives

{ip 3}

Counter Read-Only

The total number of IP packets received from all ports (including
the UART).

ipInHdrErrors

{ip 4}

Counter Read-Only

The number of packets received that were discarded due to errors
in the IP header.

ipInAddrErrors

{ip 5}

Counter Read-Only

The number of packets received that were discarded due to an
invalid (or nonroutable) destination IP address in the IP header.

ipForwDatagrams

{ip 6}

Counter Read-Only

The number of packets received that were routed towards a final
IP destination.

ipInUnknownProtos

{ip 7}

Counter Read-Only

The number of packets received that were addressed to this
ELS10-26’s IP, but were discarded because of an unknown or
unsupported protocol.

ipInDiscards

{ip 8}

Counter Read-Only

The number of packets that were received without error, but were
not processed (due to insufficient resources, for example).

This appears to be a typographical error in the TCP/IP MIB, since the name

should be ipInForwDatagrams.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands