Cabletron Systems ELS10-26 Reference Manual Download Page 37 | Manualshive

Page: 37 / 170

background image

TCP/IP MIB-II

2-11

ipInDelivers

{ip 9}

Counter Read-Only

The total number of input packets successfully delivered to the IP
user-protocol layers.

ipOutRequests

{ip 10}

Counter Read-Only

The total number of IP output packets generated by this ELS10-26.
This count does not include any packets represented in
ipForwDatagrams.

ipOutDiscards

{ip 11}

Counter Read-Only

The total number of output packets which were discarded (due to
lack of resources, for example). This counter includes packets
which would be included in ipForwDatagrams if any such packets
were discarded.

ipOutNoRoutes

{ip 12}

Counter Read-Only

The number of packets which were discarded because no route
could be found to transmit them to their destination. This counter
includes any packets counted in ipForwDatagrams which meet
this “no-route” criterion.

ipReasmTimeout

{ip 13}

Integer Read-Only

The maximum time, in seconds, that received fragments are held
while they are awaiting reassembly within this ELS10-26.

ipReasmReqds

{ip 14}

Counter Read-Only

The number of IP fragments received which needed to be
reassembled within this ELS10-26.

«
...
35
36
37
38
39
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: X-Micro Pages: 74

VigorIPPBX 2820 Series

Brand: Draytek Pages: 29

Brand: 3Com Pages: 16

Brand: NXP Semiconductors Pages: 24

Brand: Konica Minolta Pages: 38

Brand: Western Digital Pages: 8

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: Abocom Pages: 1

Brand: T.A Pages: 11

Brand: Hama Pages: 6

LIQMAX III ELC-LMT120-ARGB

Brand: ENERMAX Pages: 32

Brand: Intel Pages: 958

Brand: Patton electronics Pages: 145

Brand: Comway Pages: 20

Brand: Patton electronics Pages: 2

Brand: Dahua Pages: 113

Brand: ebm-papst Pages: 13

Brand: iDirect Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands