Cabletron Systems ELS10-26 Reference Manual Download Page 158

Page: 158 / 170

6-46

ELS10-26 MIB

STATUS

mandatory

DESCRIPTION

The hop count for a set of probes
with a particular TTL.

::= {lxtraceEntry 8}

lxtraceHopAddress OBJECT-TYPE

SYNTAX

IpAddress

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

The IP address of the host which
responded for a probe with a
particular TTL.

::= {lxtraceEntry 9}

lxtraceProbe OBJECT-TYPE

SYNTAX

INTEGER

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

The probe instance for a particu-
lar hop.

::= {lxtraceEntry 10}

lxtraceState OBJECT-TYPE

SYNTAX

INTEGER

{not-started (0),

active (1),

time-exceeded (2)

host-unreachable (3)

net-reachable (4),

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands