Cabletron Systems ELS10-26 Reference Manual Download Page 157

Page: 157 / 170

ELS10-26 MIB

6-45

STATUS

mandatory

DESCRIPTION

The number of probes which are
sent for each hop. This variable
cannot be set while lxtraceOpera-
tion is on.

::= {lxtraceEntry 5}

lxtraceWait OBJECT-TYPE

SYNTAX

TimeTicks

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

The time to wait in response to a
probe. This variable cannot be set
while lxOperation is on.

::= {lxtraceEntry 6}

lxtraceOperation OBJECT-TYPE

SYNTAX

INTEGER {on (1), off (2) }

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

Setting lxtraceOperation to on
will begin the traceroute request.
Setting lxtraceOperation to off
will terminate the traceroute
request.

::= {lxtraceEntry 7}

lxtraceHop OBJECT-TYPE

SYNTAX

INTEGER

ACCESS

read-only

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands