Cabletron Systems ELS10-26 Reference Manual Download Page 132

Page: 132 / 170

6-20

ELS10-26 MIB

lxifForwardedChars

{lxifEntry 30}

Counter Read-Only

Number of characters in the forwarded received packets.

lxifDesc

{lxifEntry 32}

lxifGoodRxFrames

{lxifEntry 33}

Counter Read-Only

lxifGoodTxFrames

{lxifEntry 34}

Counter Read-Only

6.1.7 Cabletron Dot3 Group

This group provides additional objects that are not part of the
standard dot3 MIB.

lxdot3Table

{lxdot3 1}

Not Accessible

A list of dot3 interfaces entries, one per dot3 port.

lxdot3Index

{lxdot3Entry 1}

Integer Read-Only

The port number that identifies the entry.

lxdot3TPLinkOK

{lxdot3Entry 2}

Integer Read-Only

An integer that indicates if the port’s 10BASE-T link is okay. It also
indicates if the port’s Link LED is on. Values include:

• true (1)

• false (2)

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands