Cabletron Systems ELS10-26 Reference Manual Download Page 150

Page: 150 / 170

6-38

ELS10-26 MIB

DESCRIPTION

The number of ping requests
which are to be sent. This vari-
able cannot be set while lxping-
Operation is on.

::= {lxpingEntry 4}

lxpingDataSize OBJECT-TYPE

SYNTAX INTEGER

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

The datagram packet size which
will be sent with the
ECHO_REQUEST in bytes. This
variable cannot be set while
lxpingOperation is on.

::= {lxpingEntry 5}

lxpingWait OBJECT-TYPE

SYNTAX

TimeTicks

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

The time, in centiseconds,
between the sending of each
ECHO_REQUESTmessage. This
variable cannot be set while
lxpingOperation is on.

::= {lxpingEntry 6}

lxping TimeOut OBJECT-TYPE

SYNTAX

TimeTicks

ACCESS

read-write

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands