Cabletron Systems ELS10-26 Reference Manual Download Page 54

Page: 54 / 170

2-28

TCP/IP MIB-II

snmpOutNoSuchNames

{snmp 21}

Counter Read-Only

The total number of SNMP PDUs created by the ELS10-26, with a
value of “noSuchName” in the PDU’s “ErrorStatus”.

snmpOutBadValues

{snmp 22}

Counter Read-Only

The total number of SNMP PDUs created by the ELS10-26, with a
value of “badValue” in the PDU’s “ErrorStatus”.

snmpOutReadOnlys

{snmp 23}

Counter Read-Only

All GetResponse PDUs indicate a noSuchName ErrorStatus, since
this variable is no longer used.

snmpOutGenErrs

{snmp 24}

Counter Read-Only

The total number of SNMP PDUs created by the ELS10-26, with a
value of “genErr” in the PDU’s “ErrorStatus”.

snmpOutGetRequests

{snmp 25}

Counter Read-Only

Always zero, since the ELS10-26 never creates any SNMP request
PDUs.

snmpOutGetNexts

{snmp 26}

Counter Read-Only

Always zero, since the ELS10-26 never creates any SNMP request
PDUs.

snmpOutSetRequests

{snmp 27}

Counter Read-Only

Always zero, since the ELS10-26 never creates any SNMP request
PDUs.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands