Cabletron Systems ELS10-26 Reference Manual Download Page 163 | Manualshive

Page: 163 / 170

background image

Traps

7-3

lxRxQuesTrap (4) - Sent whenever the number of times that the
port’s receiver has missed receiving packets due to buffer space
shortages has exceeded the port’s limit.

Cabletron MIB variables include:

• lxTrapSeverity

• lxifRxQueues

lxTxStormFlagTrap (5) - Sent whenever multicast storm protection
has been invoked for the port.

Cabletron MIB variables include:

• lxTrapSeverity

lxTxCongestsTrap (6) - Sent whenever packets destined for the unit
itself were discarded due to lack of buffer space.

Cabletron MIB variables include:

• lxTrapSeverity

• lxadminNamReceiveCongests

lxDebugStringIdTrap (8) - Send whenever the unit has a debug text
string to be displayed. The text strings are sent in a stream-like
fashion.

Cabletron MIB variables include:

• lxTrapSeverity

• lxdebugStringId

• lxdebugString

lxLpbkOperationTrap (9) - Send whenever the unit has finished a
loop back test, or a loop back error has been detected.

Cabletron MIB variables include:

«
...
161
162
163
164
165
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

SCSI PC Card REX-9530V

Brand: Ratoc Systems Pages: 30

Brand: 3Com Pages: 16

Brand: NETGEAR Pages: 2

nForce 680I LT SLI

Brand: Nvidia Pages: 80

Brand: Google Pages: 14

Fast SwitchHub-8mi SNMP

Brand: Accton Technology Pages: 13

Brand: N.A.T. Pages: 32

kontron COMe-cEL6

Brand: S&T Pages: 99

Brand: Waves Pages: 41

HHM Series HHM2245SA1

Brand: TDK Pages: 2

Brand: Aethra Pages: 2

Brand: Nakayo Pages: 119

NOVA300 AML02304U1

Brand: Nexxt Pages: 75

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Brand: Belden Pages: 84

Mercury FireWire 400

Brand: OWC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands