Cabletron Systems ELS10-26 Reference Manual Download Page 66

Page: 66 / 170

2-40

TCP/IP MIB-II

This MIB defines Cabletron extensions to MIB-II. Groups within
this MIB refer to the group in which the objects pertain within
MIB-II.

Groups within this MIB are:

commonDevOBJECT IDENTIFIER

{ctronMib2 1}

ctIfPortOBJECT IDENTIFIER

{ctronMib2 2}

ctIfPortOBJECT IDENTIFIER

{ctronMib2 3}

ctIfCpOBJECT IDENTIFIER

{ctronMib2 4}

ctSNMP OBJECT IDENTIFIER

{ctronMib2 5}

ctSONET OBJECT IDENTIFIER

{ctronMib2 6}

The commonDevice group of this group is an extension to the
system group MIB2. It contains similar information to that defined
within the system group of MIB-II.

Implementation of this group is optional for Cabletron devices.

comDeviceTime

OBJECT-TYPE

SYNTAX DisplayString(SIZE (8))

ACCESS

read-write

STATUS

mandatory

DESCRIPTION

The current time of day, in 24 hour
format, as measured by the device.
The representation shall use the stan-
dard HHMMSS format.

::= {commonDev 1}

comDeviceDate

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands