Cabletron Systems ELS10-26 Reference Manual Download Page 155

Page: 155 / 170

ELS10-26 MIB

6-43

::= {lxtraceTable 1}

lxtraceEntry ::= SEQUENCE

{lxtraceNMSAddr

IpAddress

lxtraceDsetAddr

IpAddress

lxtraceMaxTTL

INTEGER

lxtraceDataSize

INTEGER

lxtraceNumProbes

INTEGER

lxtraceWait

TimeTicks

lxtraceOperation

INTEGER

lxtraceHop

INTEGER

lxtraceHopAddr

IpAddress

lxtraceProbe

INTEGER

lxtraceState

INTEGER

lxtraceTime

TimeTicks}

traceNMSAddr OBJECT-TYPE

SYNTAX

IpAddress

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

The IP address of the NMS, used
to determine on which traceroute
request to return information.

::= {lxtraceEntry 1}

lxtraceDsetAddr OBJECT-TYPE

SYNTAX

IpAddress

ACCESS

read-write

STATUS

mandatory

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands