Renesas SH7706 Series Скачать руководство пользователя | Manualshive

Страница: 489 / 749

background image

Section 16 Serial Communication Interface with FIFO (SCIF)

Rev. 5.00 May 29, 2006 page 441 of 698

REJ09B0146-0500

Section 16 Serial Communication Interface with FIFO

(SCIF)

This LSI has single-channel serial communication interface with FIFO (SCIF) that supports
asynchronous serial communication. It also has 16-stage FIFO registers for both transfer and
receive that enables this LSI efficient high-speed continuous communication. Figure 16.1 shows a
diagram of the SCIF, and figures 16.2 to 16.4 show the I/O ports.

16.1

Feature

•

Asynchronous serial communication



Serial data communications are performed by start-stop in character units. The SCI can
communicate with a universal asynchronous receiver/transmitter (UART), an asynchronous
communication interface adapter (ACIA), or any other communications chip that employs
a standard asynchronous serial system. There are eight selectable serial data
communication formats.



Data length: Seven or eight bits



Stop bit length: One or two bits



Parity: Even, odd, or none



Receive error detection: Parity and framing errors



Break detection:

•

Full duplex communication

The transmitting and receiving sections are independent, so the SCI can transmit and receive
simultaneously. Both sections use 16-stage FIFO buffering, so high-speed continuous data
transfer is possible in both the transmit and receive directions.

•

On-chip baud rate generator with selectable bit rates

•

Internal or external transmit/receive clock source

From either baud rate generator (internal) or SCK2 pin (external)

•

Four types of interrupts

Transmit-FIFO-data-empty, break, receive-FIFO-data-full, and receive-error interrupts are
requested independently. The direct memory access controller (DMAC) can be activated to
execute a data transfer by a transmit-FIFO-data-empty or receive-FIFO-data-full interrupt.

•

When the SCIF is not in use, it can be stopped by halting the clock supplied to it, saving
power.

•

On-chip modem control functions (

RTS2

and

CTS2

)

«
...
487
488
489
490
491
...
»

Содержание SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7706 Series

Бренд: EAW Страницы: 6

Бренд: EAW Страницы: 6

Бренд: Vanguard Страницы: 4

Бренд: Cypress Semiconductor Страницы: 9

Бренд: Moxa Technologies Страницы: 19

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

IMACS Network Device

Бренд: Zhone Страницы: 114

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

Бренд: Sony Ericsson Страницы: 93

Digital Loudspeaker

Бренд: Dolby Laboratories Страницы: 4

Бренд: Aaeon Страницы: 100

Бренд: ZALMAN Страницы: 6

Бренд: JETWAY Страницы: 15

Бренд: Exsys Страницы: 2

Бренд: Garner Страницы: 13

Бренд: MSI Страницы: 48

Бренд: MSI Страницы: 54

Бренд: MSI Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды