Renesas SH7706 Series Скачать руководство пользователя | Manualshive

Страница: 150 / 749

background image

Section 5 Cache

Rev. 5.00 May 29, 2006 page 102 of 698
REJ09B0146-0500

5.2.2

Cache Control Register 2 (CCR2)

Cache control register 2 (CCR2) enables or disables the cache locking mechanism. This register
setting is valid only in cache locking mode. Cache locking mode is enabled when the cache
locking bit (bit 12) of the status register (SR) is set to 1, and disabled when it is cleared to 0.

If a cache miss occurs during prefetch instruction (PREF) execution in cache locking mode, one
line size of data pointed by Rn is loaded into the cache according to the W3LOAD, W3LOCK,
W2LOAD, and W2LOCK bit settings of CCR2 (bits 9, 8, 1, and 0). Table 5.2 shows the
relationship between each bit setting and the way to be replaced when the prefetch instruction is
executed. On the other hand, if a cache hit occurs during prefetch instruction (PREF) execution, no
data is loaded into the cache and entries that have been valid in the cache are maintained. For
instance, if one line size of data pointed by Rn exists at way 0, and if the prefetch instruction is
executed while the cache lock, W3LOAD, and W3LOCK are set to 1s, a cache hit occurs and data
is not brought to way 3.

When a cache is accessed by other than the prefetch instruction in cache locking mode, the ways
to be replaced are controlled by the W3LOCK and W2LOCK bit settings. Table 5.3 shows the
relationship between CCR2 bit settings and the way to be replaced.

A program to modify the CCR2 contents should be placed at an address area whose data is not
cached.

Bit

Bit Name

Initial Value

R/W

Description

31 to 10



All 0

R

Reserved

These bits are always read as 0. The write value
should always be 0.

9

8

W3LOAD

W3LOCK

0

0

W

W

W3LOAD: Way 3 load

W3LOCK: Way 3 Lock

When W3LOACK = 1 & W3LOAD = 1 & SR.CL is
1, the prefetched data will always be loaded into
Way3. In all other conditions, the prefetched data
will be loaded into the way pointed by LRU.

7 to 2



All 0

R

Reserved

These bits are always read as 0. The write value
should always be 0.

«
...
148
149
150
151
152
...
»

Содержание SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7706 Series

Бренд: Rolls Страницы: 2

Бренд: Variscite Страницы: 18

Бренд: Aaeon Страницы: 72

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: Alarm Страницы: 5

Disc Publisher XR

Бренд: Primera Страницы: 2

Power System S914

Бренд: IBM Страницы: 48

Бренд: ATI Technologies Страницы: 87

Acme Packet 3900

Бренд: Oracle Страницы: 70

Бренд: Carrier Страницы: 18

Бренд: Qvis Страницы: 233

Бренд: Westermo Страницы: 22

ClareVision CV-M161620-04

Бренд: Clare Controls Страницы: 32

StorageWorks TM RAID Array 3000 Pedestal Storage Subsystem

Бренд: Compaq Страницы: 112

Бренд: AG Страницы: 10

Бренд: Renesas Страницы: 31

Бренд: Terasic Страницы: 208

Бренд: National Datacomm Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды