manualshive.com logo in svg

Renesas SH7706 Series, Руководство по оборудованию

Серия продуктов Renesas SH7706 Series представляет собой набор высококачественных микроконтроллеров, идеально подходящих для различных промышленных приложений. Чтобы ознакомиться с подробным описанием и настройками устройства, скачайте бесплатное Hardware Manual с официального сайта manualshive.com.

Поделиться
Скачать
background image

Section 3   Memory Management Unit (MMU)

Rev. 5.00  May 29, 2006  page 55 of 698

REJ09B0146-0500

Physical Address Space: This LSI supports a 32-bit physical address space, but the upper 3 bits
are actually ignored and treated as a shadow. See section 8, Bus State Controller (BSC), for
details.

Address Translation: When the MMU is enabled, the virtual address space is divided into units
called pages. Physical addresses are translated in page units. Address translation tables in external
memory hold information such as the physical address that corresponds to the virtual address and
memory protection codes. When an access to areas P1 or P2 occurs, there is no TLB access and
the physical address is defined uniquely by hardware. If it belongs to area P0, P3 or U0, the TLB
is searched by virtual address and, if that virtual address is registered in the TLB, the access hits
the TLB. The corresponding physical address and the page control information are read from the
TLB and the physical address is determined.

If the virtual address is not registered in the TLB, a TLB miss exception occurs and processing
will shift to the TLB miss handler. In the TLB miss handler, the TLB address translation table in
external memory is searched and the corresponding physical address and the page control
information are registered in the TLB. After returning from the handler, the instruction that caused
the TLB miss is re-executed. When the MMU is enabled, address translation information that
results in a physical address space of H'80000000 to H'FFFFFFFF should not be registered in the
TLB.

When the MMU is disabled, the virtual address is used directly as the physical address. As this
LSI supports a 29-bit address space as the physical address space, the top 3 bits of the physical
address are ignored, and constitute a shadow space. For example, addresses H'00001000 in the P0
area, H'80001000 in the P1 area, H'A0001000 in the P2 area, and H'C0001000 in the P3 area are
all mapped onto the same physical address. When access to these addresses is performed with the
cache enabled, an address with the top 3 bits of the physical address masked to 0 is stored in the
cache address array to ensure data congruity.

Single Virtual Memory Mode and Multiple Virtual Memory Mode: There are two virtual
memory modes: single virtual memory mode and multiple virtual memory mode. In single virtual
memory mode, multiple processes run in parallel using the virtual address space exclusively and
the physical address corresponding to a given virtual address is specified uniquely. In multiple
virtual memory mode, multiple processes run in parallel sharing the virtual address space, so a
given virtual address may be translated into different physical addresses depending on the process.
By the value set to the MMU control register (MMUCR), either single or multiple virtual mode is
selected.

In terms of operation, the only difference between single virtual memory mode and multiple
virtual memory mode is the TLB address comparison method.

Содержание SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7706 Series

dbx 902 Manual preview
902
Бренд: dbx Страницы: 8
Supermicro SuperServer 5019S-L User Manual preview
SuperServer 5019S-L
Бренд: Supermicro Страницы: 61
Time domain PulsON 440 Datasheet And User Manual preview
PulsON 440
Бренд: Time domain Страницы: 64
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Бренд: Buffalo Страницы: 2
ETAS BR-XETK-S4.0 User Manual preview
BR-XETK-S4.0
Бренд: ETAS Страницы: 82
G&D DVI-Vision-IP-Fiber Installation And Operation Manual preview
DVI-Vision-IP-Fiber
Бренд: G&D Страницы: 240
Barracuda CloudGen Firewall Revision preview
CloudGen Firewall
Бренд: Barracuda Страницы: 8
Alpine PXE-R600 Manual preview
PXE-R600
Бренд: Alpine Страницы: 17
VIA Technologies ARTiGO-A1200 Quick Manual preview
ARTiGO-A1200
Бренд: VIA Technologies Страницы: 2
b&t RTL8720D Instruction Manual preview
RTL8720D
Бренд: b&t Страницы: 34
DataDirect Networks EF2915 Series User Manual preview
EF2915 Series
Бренд: DataDirect Networks Страницы: 97
Cambium Networks PMP/PTP 450 Series Quick Start Manual preview
PMP/PTP 450 Series
Бренд: Cambium Networks Страницы: 155
Huawei CR52-MPUA Specifications preview
CR52-MPUA
Бренд: Huawei Страницы: 3
Johnson Controls IQ WIFI Installation Manual preview
IQ WIFI
Бренд: Johnson Controls Страницы: 45
Huawei CR52-2xPOS/STM16-SFP Specifications preview
CR52-2xPOS/STM16-SFP
Бренд: Huawei Страницы: 2
Huawei E5785-320a Product Description preview
E5785-320a
Бренд: Huawei Страницы: 23
Huawei eAN3810A Hardware Installation Manual preview
eAN3810A
Бренд: Huawei Страницы: 50
Huawei CX600-X1-M Series Hardware Description preview
CX600-X1-M Series
Бренд: Huawei Страницы: 234

Бренды по названию

Популярные бренды

Загрузить еще бренды