Renesas SH7706 Series Скачать руководство пользователя | Manualshive

Страница: 61 / 749

background image

Section 2 CPU

Rev. 5.00 May 29, 2006 page 13 of 698

REJ09B0146-0500

Section 2 CPU

2.1

Register Description

2.1.1

Privileged Mode and Banks

Processor Modes: There are two processor modes: user mode and privileged mode. The SH7706
normally operates in user mode, and enters privileged mode when an exception occurs or an
interrupt is accepted. There are three kinds of registers—general registers, system registers, and
control registers—and the registers that can be accessed differ in the two processor modes.

General Registers: There are 16 general registers, designated R0 to R15. General registers R0 to
R7 are banked registers which are switched by a processor mode change. In privileged mode, the
register bank bit (RB) in the status register (SR) defines which banked register set is accessed as
general registers, and which set is accessed only through the load control register (LDC) and store
control register (STC) instructions.

When the RB bit is 1, BANK1 general registers R0_BANK1 to R7_BANK1 and non-banked
general registers R8 to R15 function as the general register set, with BANK0 general registers
R0_BANK0 to R7_BANK0 accessed only by the LDC/STC instructions.

When the RB bit is 0, BANK0 general registers R0_BANK0 to R7_BANK0 and nonbanked
general registers R8 to R15 function as the general register set, with BANK1 general registers
R0_BANK1 to R7_BANK1 accessed only by the LDC/STC instructions. In user mode, the 16
registers comprising bank 0 general registers R0_BANK0 to R7_BANK0 and non-banked
registers R8 to R15 can be accessed as general registers R0 to R15, and bank 1 general registers
R0_BANK1 to R7_BANK1 cannot be accessed.

Control Registers: Control registers comprise the global base register (GBR) and status register
(SR) which can be accessed in both processor modes, and the saved status register (SSR), saved
program counter (SPC), and vector base register (VBR) which can only be accessed in privileged
mode. Some bits of the status register (such as the RB bit) can only be accessed in privileged
mode.

System Registers: System registers comprise the multiply and accumulate registers
(MACL/MACH), the procedure register (PR), and the program counter (PC). Access to these
registers does not depend on the processor mode.

The register configuration in each mode is shown in figures 2.1.

«
...
59
60
61
62
63
...
»

Содержание SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7706 Series

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 5

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

Бренд: Salusfin Страницы: 6

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренд: JETWAY Страницы: 55

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

NIC-FC730i-Mb-2-32G

Бренд: H3C Страницы: 37

Бренд: Sangoma Страницы: 6

Бренд: PMD Страницы: 74

ExpressBox2 EB2

Бренд: Magma Страницы: 74

Бренд: Laser Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды