Renesas SH7706 Series Скачать руководство пользователя страница 411 | Manualshive

Страница: 411 / 749

background image

Section 14 Serial Communication Interface (SCI)

Rev. 5.00 May 29, 2006 page 363 of 698

REJ09B0146-0500

Section 14 Serial Communication Interface (SCI)

This LSI has an on-chip serial communication interface (SCI) that supports both asynchronous and
clock synchronous serial communication. It also has a multiprocessor communication function for
serial communication among two or more processors. A block diagram of SCI is shown in figure
14.1, and the I/O ports are shown in figures 14.2 to 14.4.

14.1

Feature

The SCI has the following features.

•

Selectable from asynchronous or clock synchronous as the serial communications mode

Asynchronous mode:



Serial data communications are synched by start-stop in character units. The SCI can
communicate with a universal asynchronous receiver/transmitter (UART), an asynchronous
communication interface adapter (ACIA), or any other communications chip that employs
a standard asynchronous serial system. It can also communicate with two or more other
processors using the multiprocessor communication function. There are 12 selectable serial
data communication formats.



Data length: Seven or eight bits



Stop bit length: One or two bits



Parity: Even, odd, or none



Multiprocessor bit: 1 or 0



Receive error detection: Parity, overrun, and framing errors



Break detection: By reading the RxD0 pin level directly from the port Serial
communication port data register (SCPDR) when a framing error occurs

Clock synchronous mode:



Serial data communication is synchronized with a clock signal. The SCI can communicate
with other chips having a clock synchronous communication function. One serial data
communication format is available.



Data length: Eight bits



Receive error detection: Overrun errors

•

Full duplex communication

The transmitting and receiving sections are independent, so the SCI can transmit and receive
simultaneously. Both sections use double buffering, so continuous data transfer is possible in
both the transmit and receive directions.

«
...
409
410
411
412
413
...
»

Содержание SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7706 Series

Бренд: dbx Страницы: 8

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 15

EK-FC780 GTX Jetstream

Бренд: ekwb Страницы: 2

Бренд: Alesis Страницы: 61

ACC-CX3RDK-CU5640

Бренд: e-con Systems Страницы: 9

Бренд: FS Страницы: 19

Бренд: Quantum Страницы: 7

AT32F421 Series

Бренд: ARTERY Страницы: 337

Бренд: Bailey Страницы: 33

TeleMyo 2400T V2

Бренд: Noraxon Страницы: 52

Бренд: National Instruments Страницы: 52

MULTIflight Stick

Бренд: Multiplex Страницы: 10

NexXxoS GPX-N 1070-M08

Бренд: Alphacool Страницы: 4

PCI4-AD-x16HI-BG4

Бренд: Serial Cables Страницы: 15

Бренд: XtendLan Страницы: 17

Бренд: Netopia Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды