Renesas SH7706 Series Скачать руководство пользователя | Manualshive

Страница: 379 / 749

background image

Section 12 Timer Unit (TMU)

Rev. 5.00 May 29, 2006 page 331 of 698

REJ09B0146-0500

Bit

Bit Name

Initial Value

R/W

Description

5

UNIE

0

R/W

Underflow Interrupt Control

Controls enabling of interrupt generation when the
status flag (UNF) indicating TCNT_2 underflow has
been set to 1.

0: Interrupt due to UNF (TUNI) is not enabled.

1: Interrupt due to UNF (TUNI) is enabled.

4

3

CKEG1

CKEG0

0

0

R/W

R/W

Clock Edge

These bits select the external clock edge when the
external clock is selected, or when the input capture
function is used.

00: Count/capture register set on rising edge

01: Count/capture register set on falling edge

1X: Count/capture register set on both rising and falling

edge

Note: X: Don't care.

2

1

0

TPSC2

TPSC1

TPSC0

0

0

0

R/W

R/W

R/W

Timer Prescalers

These bits select the TCNT_2 count clock.

000: Internal clock: count on P

φ

/4

001: Internal clock: count on P

φ/

16

010: Internal clock: count on P

φ

/64

011: Internal clock: count on P

φ

/256

100: Internal clock: count on clock output of on-chip

RTC (RTCCLK)

101: External clock: count on TCLK pin input

110: Reserved (Setting prohibited)

111: Reserved (Setting prohibited)

12.3.4

Timer Constant Registers 0 to 2 (TCOR_0 to TCOR_2)

TCOR_0 to TCOR_2 are specified the setting value for TCNT_0 to TCNT_2 when TCNT_0 to
TCNT_2 are underflowed. TMU has 3 timer constant registers, one for each channel.

TCOR_0 to TCOR_2 is a 32-bit read/write register. TCOR is initialized to H'FFFFFFFF by a
power-on reset or manual reset; it is not initialized in standby mode, and retains its contents.

«
...
377
378
379
380
381
...
»

Содержание SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7706 Series

Бренд: Garland Страницы: 6

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

Proventia A1204

Бренд: Internet Security Systems Страницы: 42

Бренд: Comway Страницы: 20

Бренд: FiberHome Страницы: 2

Бренд: M-system Страницы: 4

Бренд: Alesis Страницы: 11

Бренд: NXP Semiconductors Страницы: 1202

Бренд: ETAS Страницы: 36

Бренд: Infoblox Страницы: 44

Бренд: Thecus Страницы: 148

Бренд: ICP DAS USA Страницы: 8

Бренд: IEI Technology Страницы: 213

Бренд: Siemens Страницы: 5

Бренд: CAMBRIONIX Страницы: 40

Бренд: 8e6 Technologies Страницы: 22

Bluetooth2 click

Бренд: mikroElektronika Страницы: 2

Бренд: Arduino Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды