Raritan PX-1000 Series Скачать руководство пользователя

Страница: 266 / 442

Chapter 7: Using the Command Line Interface

251

Reliability Error Log

This command shows the reliability error log.

show reliability errorlog <n>

Variables:



<n> is one of the options:

(zero) or any other integer number.

Option

Description

Displays all entries in the reliability error log.

Tip: You can also type the command without adding
this option "0" to get all data.

A specific
integer number

Displays the specified number of last entries in the
reliability error log.

Command History

This command syntax shows the command history for current connection
session.

show history

Displayed information:



A list of commands that were previously entered in the current session
is displayed.

History Buffer Length

This command syntax shows the length of the history buffer for storing the
history commands.

show history bufferlength

Displayed information:



The current history buffer length is displayed.

Examples

This section provides examples of the show command.

Содержание PX-1000 Series


























































































































































































































































































































































































































































Результаты поиска

Содержание PX-1000 Series

Отзывы:

Похожие инструкции для PX-1000 Series

Бренды по названию

Популярные бренды

Raritan PX-1000 Series, Руководство пользователя

Результаты поиска

Содержание PX-1000 Series

Отзывы:

Похожие инструкции для PX-1000 Series

Бренды по названию

Популярные бренды