Raritan PX-1000 Series Скачать руководство пользователя страница 66

Страница: 66 / 442

Chapter 4: Using the PDU

PX-1000 Series

These PDUs are NOT outlet-switching capable models so all outlets are
always in the ON state.

Outlet LEDs are not available.

PX-2000 Series

These models are outlet-switching capable PDUs. A small LED is adjacent
to each outlet to indicate the state of the relay board.

LED state

Outlet status

What it means

Not lit

Powered OFF

The outlet is not connected to power, or the control
circuitry's power supply is broken.

ON and LIVE

LIVE power. The outlet is on and power is available.

Red

ON and NOT LIVE

The outlet is turned on but power is not available
because a circuit breaker has tripped.

Connection Ports

Depending on the model you purchased, the total number of ports
available varies.



For most of Zero U models, there are 6 ports located on the front panel
as shown below.

Содержание PX-1000 Series


























































































































































































































































































































































































































































Результаты поиска

Содержание PX-1000 Series

Отзывы:

Бренды по названию

Популярные бренды

Raritan PX-1000 Series, Руководство пользователя

Результаты поиска

Содержание PX-1000 Series

Отзывы:

Бренды по названию

Популярные бренды