Raritan PX-1000 Series Скачать руководство пользователя страница 375

Страница: 375 / 442

Chapter 7: Using the Command Line Interface

360

config:#

role modify tester addPrivileges changeAuthSettings removePrivileges
firmwareUpgrade

Results:



The "changeAuthSettings" (Change Authentication Settings) privilege
is added to the role.



The "firmwareUpgrade" (Firmware Upgrade) privilege is removed
from the role.

Deleting a Role

This command syntax deletes an existing role.

config:#

role delete <name>

Example

The following command deletes an existing role.

config:#

role delete tester

EnergyWise Configuration Commands

An EnergyWise configuration command begins with

energywise

Enabling or Disabling EnergyWise

This command syntax determines whether the Cisco

EnergyWise

endpoint implemented on the Dominion PX device is enabled.

config:#

energywise enabled <option>

Variables:



<option> is one of the options:

true

false

Option

Description

true

The Cisco EnergyWise feature is enabled.

false

The Cisco EnergyWise feature is disabled.

Содержание PX-1000 Series


























































































































































































































































































































































































































































Результаты поиска

Содержание PX-1000 Series

Отзывы:

Бренды по названию

Популярные бренды

Raritan PX-1000 Series, Руководство пользователя

Результаты поиска

Содержание PX-1000 Series

Отзывы:

Бренды по названию

Популярные бренды