Raritan PX-1000 Series Скачать руководство пользователя | Manualshive

Страница: 270 / 442

background image

Chapter 7: Using the Command Line Interface

255

Setting the Outlet Power-On Sequence

This section only applies to outlet-switching capable PDUs.

This command syntax sets the outlet power-on sequence when the PDU
powers up.

config:#

pdu outletSequence <option>

Variables:



<option> is one of the options:

default

, or a comma-separated list of

outlet numbers.

Option

Description

default

All outlets are switched ON in the ASCENDING
order (from outlet 1 to the final outlet) when the
Dominion PX device powers up.

A comma-
separated list of
outlet numbers

All outlets are switched ON in the order you specify
using the comma-separated list.

The list must include all outlets on the PDU.

Example

The following command causes a 10-outlet PDU to first power on the 8th
to 6th outlets and then the rest of outlets in the ascending order after the
PDU powers up.

config:#

pdu outletSequence 8-6,1-5,9,10

Setting the Outlet Power-On Sequence Delay

This section only applies to outlet-switching capable PDUs.

This command syntax sets the delays (in seconds) for outlets when
turning on all outlets in sequence.

«
...
268
269
270
271
272
...
»

Содержание PX-1000 Series



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PX-1000 Series

Бренд: T+A Elektroakustik Страницы: 16

Бренд: CYP Страницы: 20

Бренд: Woodward Страницы: 125

Distribution Unit

Бренд: SmartPower Страницы: 34

Бренд: Pacific Power Source Страницы: 130

Бренд: RMS Страницы: 10

Бренд: ETA Systems Страницы: 12

eco PDU PE series

Бренд: NRGence Страницы: 91

Бренд: LDG Страницы: 6

Бренд: EV-OPTIMIZER Страницы: 8

Бренд: ADTRAN Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды