Raritan PX-1000 Series Скачать руководство пользователя страница 427

Страница: 427 / 442

Appendix F: Additional Dominion PX Information

412

SecureLock™ Outlets and Cords

SecureLock

™

is an innovative mechanism designed by Raritan, which

securely holds C14 or C20 plugs that are plugged into Raritan PDUs in
place. This method requires the following two components:



Raritan PDU with SecureLock

™

outlets, which have a latch slot inside

either side of the outlet.



SecureLock

™

cords, which is a power cord with a locking latch on

either side of its plug. The following diagram illustrates such a plug.

Item

Description

Latches on the SecureLock

™

cord's plug

Only specific PDUs are implemented with the SecureLock

™

mechanism. If

you PDU does not have this design, do NOT use the SecureLock

™

cords

with it.

Tip: The SecureLock

™

outlets can accept regular power cords for power

distribution but the SecureLock

™

mechanism does not take effect.

To lock a power cord using the SecureLock

™

mechanism:

1. Verify that the SecureLock

™

cord you purchased meets your needs.



The cords' female socket matches the power socket type (C14 or

C20) on your IT equipment.



The cord's male plug matches the outlet type (C13 or C19) on your

PDU.

2. Connect the SecureLock

™

cord between the IT equipment and your

PDU.



Plug the female socket end of the cord into the power socket of the

desired IT equipment.



Plug the male plug end of the cord into the appropriate

SecureLock

™

outlet on the PDU. Push the plug toward the outlet

until you hear the click, which indicates the plug's latches are
snapped into the latch slots of the outlet.

Содержание PX-1000 Series


























































































































































































































































































































































































































































Результаты поиска

Содержание PX-1000 Series

Отзывы:

Бренды по названию

Популярные бренды

Raritan PX-1000 Series, Руководство пользователя

Результаты поиска

Содержание PX-1000 Series

Отзывы:

Бренды по названию

Популярные бренды