Raritan PX-1000 Series Скачать руководство пользователя страница 268

Страница: 268 / 442

Chapter 7: Using the Command Line Interface

253

Example 4 - In-Depth PDU Information

More information is displayed when typing the

show pdu details

command.

Configuring the Dominion PX Device and Network

To configure the Dominion PX device or network settings through the CLI,
you must log in as the administrator.

Entering the Configuration Mode

You must enter the configuration mode since configuration commands
function in the configuration mode only.

To enter the configuration mode:

1. Ensure you have entered the administrator mode and the # prompt is

displayed.

Note: If you enter the configuration mode from the user mode, you
may have limited permissions to make configuration changes. See

Different CLI Modes and Prompts

(on page 233).

2. Type

config

and press Enter. The config:# prompt appears,

indicating that you have entered the configuration mode.

3. Now you can type any configuration command and press Enter to

change the settings.

Содержание PX-1000 Series


























































































































































































































































































































































































































































Результаты поиска

Содержание PX-1000 Series

Отзывы:

Бренды по названию

Популярные бренды

Raritan PX-1000 Series, Руководство пользователя

Результаты поиска

Содержание PX-1000 Series

Отзывы:

Бренды по названию

Популярные бренды