Raritan PX-1000 Series Скачать руководство пользователя

Страница: 39 / 442

Chapter 3: Installation and Configuration

where <mode> is either

wired

for wired connection (default) or

wireless

for wireless connection.

b. For the wired network mode, you may configure the LAN interface

settings. In most scenarios, the default setting (auto) works well
and should not be changed unless required.

To set

Use this command

LAN interface
speed

network interface
LANInterfaceSpeed <option>

where <option> is

auto

10Mbps

, or

100Mbps

LAN interface
duplex mode

network interface
LANInterfaceDuplexMode <mode>

where <mode> is

half

full

auto

Tip: You can combine multiple commands to configure multiple
parameters at a time. For example,

network interface LANInterfaceSpeed <option>
LANInterfaceDuplexMode <mode>

c. For the wireless network mode, you must configure the Service

Set Identifier (SSID) parameter.

To set

Use this command

SSID

network wireless SSID <ssid>

where <ssid> is the SSID string.

If necessary, configure more wireless parameters shown in the
following table.

To set

Use this command

BSSID

network wireless BSSID <bssid>

where <bssid> is the AP MAC address.

Содержание PX-1000 Series


























































































































































































































































































































































































































































Результаты поиска

Содержание PX-1000 Series

Отзывы:

Похожие инструкции для PX-1000 Series

Бренды по названию

Популярные бренды

Raritan PX-1000 Series, Руководство пользователя

Результаты поиска

Содержание PX-1000 Series

Отзывы:

Похожие инструкции для PX-1000 Series

Бренды по названию

Популярные бренды