manualshive.com logo in svg

Pitney Bowes Relay 5000, Руководство оператора, Страница: 70 / 202

Поделиться
Скачать
Pitney Bowes Relay 5000 Скачать руководство пользователя страница 70

3-26

SV63136  Rev.  A  

3 • Basic Operation 

SwiftStart

™ 

Jobs

SwiftStart

™

 mode allows you to run a simple job without entering any setup 

information. In SwiftStart

™

 mode, the system automatically senses the mate-

rial and sets the required parameters for running the job. A SwiftStart

™

 job 

can be run without saving the settings, or a Supervisor/Manager can name 

and save the job for future recall and use.
Use SwiftStart

™

 when your mail piece consists of only a small number of 

sheets of one size that can be folded.
•  A single sheet and a single insert will be taken from each loaded feeder, 

giving a maximum mail piece content of:  four sheets and three inserts 

(Relay 50000/6000) or four sheets and four inserts (Relay 7000/8000). 

Fold will be determined by sheet length and envelope depth.

NOTE: 

 The maximum content options are available only when two HCSFs 

are present.

•  Maximum sheet length is 11-5/8 inches (297mm)
•  Only envelope depths of 4-1/4inches to 6-3/8 inches (109mm, 111mm, 

114mm, 121mm and 162mm) can be used.

•  Cannot be used to run fold only or inserts only.
•  Cannot link feeders in this mode.
•  Envelope sealer is always on (except on trial piece).
•  Batch count is always off.
•  This mode will not work with scanning.
•  Address should be at the top of the sheet.

Starting the Job

When your Trial Piece is verified, you are ready to start running the job. To 

do this:
1.  Make sure that you are in the Home screen.
2.  Press 

START

. The system will begin running the job.

Содержание Relay 5000











































































































































































































Отзывы:

Нет отзывов