Pitney Bowes Relay 5000 Скачать руководство пользователя страница 17

Страница: 17 / 202

SV63136 Rev. A

1-7

Introduction • 1

• To obtain supplies and/or Material Safety Data Sheets, contact your

system supplier. Refer to the

Contact Information List

at the front of this

guide for more information.

• Operation of this equipment without periodic maintenance will inhibit

optimum operating performance and could cause the equipment to

malfunction. Contact your system supplier for the required service

schedule.

• Always follow specific occupational safety and health standards for your

workplace.

• To reduce the risk of fire or electrical shock, DO NOT attempt to remove

covers or disassemble the control panel or its base. The cabinet

encloses hazardous parts. If you should damage the unit, contact your

system supplier. Refer to the

Contact Information List

at the front of this

guide for more information.

• This device is not intended for use in the direct field of view at visual

display workplaces. To avoid incommoding reflexions at visual display

workplaces, this device must not be placed in the direct field of view.

If your stacker has an AC adapter to power the stacker:

• Use only the AC adapter designed specifically for the stacker. Third-party

AC adapters may damage the stacker.

• To protect against electrical shock, plug the AC adapter power cord into

a properly grounded wall outlet.

• DO NOT route the AC adapter cable over sharp edges or trap it between

furniture.

Safety

Information

(continued)

Warning Labels

The following warning labels are attached to modules on the system to alert

you to potential injury that could occur with careless operating procedures.

These same labels will be shown throughout the manual as they apply to

the various modules that are discussed in that section.

NOTICE

CAUTION

Moving mechanism can result

in personal injury.

Keep hands, long hair, ties,

jewelry and loose clothing

away from moving parts.

CAUTION

Moving mechanism can result in

personal injury.

Keep hands, long hair, ties,

jewelry and loose clothing away

from moving parts.

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 17 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: