Pitney Bowes Relay 5000 Скачать руководство пользователя страница 55

Страница: 55 / 202

SV63136 Rev. A

3-11

Basic Operation • 3

3. Using the side guide adjustor,, move the side guides in until they lightly

touch the material on both sides.

When you release the adjustor, the guides will automatically spring back

to a position that will allow for proper clearance during feeding of the

material in the tray.

NOTE:

Side guides only spring back after they are moved inward.

4. Lift the separator and load material into the tray.

NOTE:

Do not load material above the maximum fill line in the tray.

For more information on side guide adjustments, see

Adjusting Tray Side

Guides

in this chapter.

Loading a Sheet Tray

NOTE:

To view a demo of the sheet tray loading and side guide adjustment

processes: go to the Home screen and select “Loading Instructions and Pre-Run

Adjustments”. Use the UP/DOWN arrow keys to select a Sheet (being fed by the

Feeder Tower) from the Mail Piece Icon Tree, then select “Feeders Setup Demo”.

To load media into a sheet tray:
1. Using the side guide adjustor, open the sides of the tray wide enough to

clear the width of the material.

2. Fan a small stack of material and then place it into the tray, in the

orientation specified in the loading instructions on the Home screen.

Loading Material

into the Trays

(continued)

Home Screen

Home

Job: ABC

Low Sealant

Select Another Job

SwiftStart

Loading Instructions and

Pre-Run Adjustments

Run Trial Piece

Job Items

Pieces :1658

Содержание Relay 5000










































































































































































































Результаты поиска

Содержание Relay 5000

Отзывы:

Pitney Bowes Relay 5000, Руководство оператора, Страница: 55 / 202

Результаты поиска

Содержание Relay 5000

Отзывы: